BEKO Dishwasher Error Codes

I have a DSFS 6530 X which gives a F:t1 error code.
I have been facing troubles with the push buttons

That seems like an odd readout, if you have been having problems with the push buttons the first place to start would be the button panel pcb. I can’t see the board on our suppliers site for that model but there is a good chance that it will be the main pcb of the dishwasher.

Hi, I have a Beko DSFS1531S slimline dishwasher and the error code readout is P3 (the third light ) I read that this indicates an NTC error and having replaced that part the dishwasher is still not allowing the start button to work and still shows the same error. PLEASE HELP!

J

You need to test the heater for earth faults, preferably with an insulation tester at 500v. Also test other components. Engineers will eliminate other causes to try to avoid just changing the PCB. Unfortunately if you don’t think it can be other components or wiring then you might have to try the board. One reason to get a repair company like us out is that they will take on the risk of buying parts unnecessarily.

Hey their I have a Beko dishwasher here model dfn16420x flashing p1 p2 won’t start or anything
Wonder If you’s had anything like thus happen..

Thanks in regard

These are 2 different faults, P1 is Overflow so there is probably water in the base, P2 is no water.
I suggest checking to see if there is an internal leak first causing water in the base.

I have a beko pro smart inverter dishwasher and wont do any of the settings ive resetted checked hoses etc comes up with E02 tried all the settings

Hi, I will need the model number to look up the fault infomation.

Hi

We have a beko dsfn 1530

Had no heat.
The inline heater tested faulty across one thermostat

Changed heater
No heat
Tested heater all good.
Looked all over inc taking door panel off. Cannot see anything obvious
Had two lights on from continuously blinking. Wash and dry.

I’ve now held down cancel and the lights have stopped blinking
Tried a 60 degree wash cycle
Still no heat
Advice well received !

Thanks

I have a Beto DFN16X20X dishwasher. The programme panel is showing P1and and P2 flashing together and I am unable to change this. I have switched off at the mains for about an hour and retried but still the same. Can you help at all?
Thanks.

Hi I have a beko dw603

I have replaced the board the heater and water inlet and still not filling or going through a cycle

When I hold the start and pause button for 7secs I get a p3 and p6 lit and it’s fills and drains then stops then when turn it of and on again still no full but drains and keeps trying to drain

So I Have Beko DSFN 6830 when I go to function test mode and start after program one I have b:SL flashing on the screen and I need put start again to go to program 2 and same happened after finishing program 2 I need press start again. P3 goes smooth automatically move to P4 and P5 and P6 and P7 and P8 after Program 8 same thing is happening and I need press start again. No H error codes.

Also twice the function test was stock on the end of P3 like the water been pump out but dishwasher was trying for hours to pump remaining water.

So I Have Beko DSFN 6830 when I go to function test mode and start after program one I have b:SL flashing on the screen and I need put start again to go to program 2 and same happened after finishing program 2 I need press start again. P3 goes smooth automatically move to P4 and P5 and P6 and P7 and P8 after Program 8 same thing is happening and I need press start again. No H error codes

Hi there, i have a problem with a oven bekko, when it start a few seconds later turn off, and apears a AF20 error, can u help me? I dont have the name product, sadly i lost the papers !